Fixes: Problem Resolved: [SNMP] dot11SecAccountingServerPort node cannot get value. [WEB] When VLAN state is enabled, change the MSSID’s security will disable MSSID’s state. [Firmware] STA couldn’t connect to multi-ssid of 11a band when eth, wlan0, wlan1 use the same mac address. So change the mac address rule back to original [Firmware] It should send an IAPP-ADD-Notify packet when STA roaming to AP2 from AP1, not only an IAPP-Move-Notify packet. [Firmware] Change the MAC address rule, eth, wlan0, wlan1 use the same mac address. [SNMP] Fix SNMP show "00:00:00:00:00:00" mac address in 11A band. [MIB] Support WDS client info. [FW] Intel WiFi Link 4965AGN can’t connect to AP if authentication is WPA/WPA2 PSK, and vlan state is enabled. [FW] Fix the Microsoft SilverlightIE compatibility issue. [FW] AP couldn’t connect to fast radius. [FW] Modify the channel list in 11a band for U3 domain. [FW] Enhance the MSSID over WDS function, allow user change the security settings of MSSID when the ap mpde is WDS with AP. [FW]Support maximum community string length to 32 characters. [WEB] The Vlan tag mode should be set to Manual when Authentication is not WPA in multi-ssid page. [WEB] If enable Vlan state when the AP mode is WDS, it should pop up a warning message. [WEB] AP will crash if save Rouge AP detection info before the Radar scan complete. [WEB] User can’t configure a valid IP address(such as X.255.X.X or X.X.255.X) as a DHCP Start Address in DHCP Server page. [FW] A/G band IGMP snp cannot play simultaneous [WEB] The dynamic vlan mode can not set successful on the multi-ssid page of 802.11a. [WEB] If set the authentication to WPA-EAP, the multi-ssid page display imperfectly. [WEB] User can’t set Wireless MAC ACL. [WEB] If ap mode is not normal ap, then Grouping should be gray and can't set. [WEB] Enable VLAN State when the multi state is disabled, the radio button of band should point to “both”. [WEB] There should be a warning message, when changing primary ssid’s authentication will affect MSSID’s authentication. [CLI] When WDS or WDS with AP mode is set, disable CLI command about ratecontrol and supportrate. [FW] Only permit user manage the ap through Lan1. [FW] Mssid over WDS function has some conflict with Mssid Eth to WM filter policy, it won’t take effect if the Mssid Eth to WM filter policy is enable. [FW] Broadcast packets may miss four bytes if Vlan is enable, this will cause two station can not communicate between 802.11a&802.11g on the same vlan. [FW] Trap can’t send. [FW]When MSSID is enabled and authentication type is WPA-PSK in secondary SSID, the STAs which associated to secondary SSID failed to ping each other. Enhancements: [FW] Support APMII v2.0. [FW] Modify the channel list in 11a band as the latest output power table sepc. [FW] Support NAP function based on dynamic vlan. [FW] Support Primary SSID with VLAN tag function [FW] Support Administration VLAN(Manage VLAN) , administrate AP with WLAN and management IP range function [FW] Trap server settings(categorize the types of traps) [FW] Support MSSID over WDS [FW] WMM over WDS [FW] Priority by SSID [FW] IGMP Snooping (v1/v2) [FW] 802.1X Dynamic VLAN [FW] Data Rate Control follows Dlink new spec. [FW] Support IAPP (fast roaming) [FW] Enable/Disable ping Secondary RADIUS server setting [FW] AP status on UI (also on MIB) CPU and Memory utilization Statistics for Ethernet TX and RX bytes and packets [WEB]SSID change wireless network name (SSID) [MIB]Support 802.11MIB [MIB]Support MIB-II (RFC-1213) [MIB]Support Trap002-1 spec [CLI] CLI command to input SNMP Location. [CLI] Hide the commands, get targetPower/gett controlPower/get swPower ,in CLI [CLI]Open 3 RSTP commands, rstp getstp/rstp getstate/rstp setstate Please do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games. Note: Try to set a system restore point before installing a device driver. It will help you restore system if installed driver not complete.